Loading
  • Customer Inquiries
  • Employee Login
Park City Drilling Technologies
  • Home
  • Drilling Motors
    • Millennium Motor Assemblies
      • Oil Sealed
      • HDD Oil Sealed
      • Mud Lubricated
      • Short Bit-to-Bend
      • Motor Handbook (PDF)
  • Drilling Jars
    • Ultimate Drilling Jars
      • Ultimate Double Acting Hydraulic
    • Conventional Drilling Jars
      • Double Acting Hydraulic
      • Double Acting Hydraulic / Mechanical
  • Vibration Tools
    • SHAKER
  • Drilling Tools
    • Downhole Shock Tool
  • Company
    • Officers
    • HS&E
  • Contact Us

Ultimate Double Acting Hydraulic Drilling Jar

UHJDA Product Flyer

Ultimate Drilling Jar Brochure

Product Catalog

Imperial

Nominal OD
(inch)
Length
(ft)
Thru Bore
(inch)
Tensile Yield
(lbs)
Torsional Limit
(ft-lbs)
Max Pull During Delay
(lbs)
Free Stroke Up / Down
(inch)
Total Stroke
(inch)
4.7522.02.25370 60021 500132 0008.025.0
6.5023.12.751 220 00051 000275 0008.025.0
6.7522.72.751 220 00051 000290 0008.025.0
7.0022.72.751 220 00051 000290 0008.025.0
8.0023.22.81 1 293 900103 200400 0008.025.0
9.5024.1 3.002 106 900189 300550 0008.025.0

Metric

Nominal OD
(mm)
Length
(m)
Thru Bore
(mm)
Tensile Yield
(daN)
Torsional Limit
(Nm)
Max Pull During Delay
(daN)
Free Stroke Up / Down
(mm)
Total Stroke
(mm)
1216.757164 80029 10058 700200640
1657.070542 70069 100122 300200640
1716.970542 70069 800129 000200640
1786.970542 70069 800129 000200640
2037.171575 500139 900177 900200640
2417.376937 100256 700244 600200640

Ultimate Double Acting Hydraulic Drilling Jar

Using proprietary new technology, Park City has been able to dramatically increase the allowable overpull force. The Ultimate Double Acting Hydraulic Drilling Jar (UHJDA) is a bi-directional drilling jar incorporating hydraulic delay without a latch mechanism.  This jar will allow the operator to apply variable impact in both the up and down directions.  The UHJDA is intended for use in highly deviated or high friction wells, where conditions may prevent applying sufficient force to release a mechanical latch.

Features & Benefits
  • The UHJDA is hydraulically controlled and jars in both directions, with impact force controlled by the operator.
  • Impact force is controlled by a metering device that ensures consistent delay times over the full range of operating temperatures.
  • The UHJDA operates via a simple up and down motion and is unaffected by right- or left-hand torque.
  • Standard seals are suitable for use up to 250°F (120°C). Optional high temperature seal kits are available for service to 400°F (200°C). External sealing surfaces are tungsten carbide-coated to enhance wear and corrosion resistance.
Operation

Jarring Up

  • With the jar in the neutral position, apply the desired overpull in excess of the free string weight, starting the hydraulic delay sequence. At the end of the hydraulic delay, the jar will release causing an upward impact force.
  • If necessary, lower the drill string sufficiently to close the jar to the neutral position, ready to jar up again.

Jarring Down

  • With the jar in the neutral position, lower the drill string to apply the desired down force, starting the hydraulic delay sequence. At the end of the hydraulic delay, the jar will release causing a downward impact force.
  • If necessary, raise the drill string sufficiently to open the jar to the neutral position, ready to jar down again.
Handling
  • To prevent unintentional tripping during handling, the UHJDA is fitted with a safety clamp to keep the jar in the fully extended position. The safety clamp must remain installed until the jar is ready to run into the hole.
  • When preparing to run into the hole, connect the jar to the drill string and apply tension before removing the safety clamp.
  • When coming out of the hole, install the safety clamp while the jar is still under tension and fully extended.
Gallery

Ultimate Double Acting Hydraulic Drilling Jar

UHJDA Product Flyer

Ultimate Drilling Jar Brochure

Product Catalog

Technical Specifications

Imperial

Nominal OD
(inch)
Length
(ft)
Thru Bore
(inch)
Tensile Yield
(lbs)
Torsional Limit
(ft-lbs)
Max Pull During Delay
(lbs)
Free Stroke Up / Down
(inch)
Total Stroke
(inch)
4.7522.02.25370 60021 500132 0008.025.0
6.5023.12.751 220 00051 000275 0008.025.0
6.7522.72.751 220 00051 000290 0008.025.0
7.0022.72.751 220 00051 000290 0008.025.0
8.0023.22.81 1 293 900103 200400 0008.025.0
9.5024.1 3.002 106 900189 300550 0008.025.0


Metric

Nominal OD
(mm)
Length
(m)
Thru Bore
(mm)
Tensile Yield
(daN)
Torsional Limit
(Nm)
Max Pull During Delay
(daN)
Free Stroke Up / Down
(mm)
Total Stroke
(mm)
1216.757164 80029 10058 700200640
1657.070542 70069 100122 300200640
1716.970542 70069 800129 000200640
1786.970542 70069 800129 000200640
2037.171575 500139 900177 900200640
2417.376937 100256 700244 600200640

Specifications are based on as new condition and are subject to change without notice.

Sales & Rental Inquiries

Download Catalog

© Copyright | Park City Drilling Technologies. All Rights Reserved.
Brad Martens

Brad Martens has 39 years of experience in management and sales roles, both domestic and international. A belief in quality and performance of products sets Park City apart from competitors. Providing value and putting the customer first is critical to our success.

Bob Howard

Mr. Howard has 46 years industry experience and has held operations management positions both domestically and internationally.  Bob  is a strong proponent of “uncompromised quality” with a dedicated commitment to meeting Customers’ performance expectations.

Bob Ferguson

Bob Ferguson is the CFO of the newly formed Park City Drilling Technologies. Bob has more than 30 years experience and has held various senior financial roles in the oil and gas industry.

Message

Send us mail

Scroll to top